Facebook
Categories
Categories

Slewing Bearing Material Selection: A Practical Guide to Grades & Applications

Oct 12th,2026 103 Views

Introduction

A slewing bearing is the load-bearing pivot at the heart of cranes, excavators, wind turbines, telescopic handlers and countless rotating platforms. It carries enormous radial, axial and tilting-moment loads simultaneously, and it must do so reliably, often for decades of continuous service.

The materials used in a slewing bearing determine not only its load capacity and service life, but also its resistance to impact, wear, corrosion and temperature extremes. Choosing the right material for each component is therefore one of the most important engineering decisions in a bearing’s design. This guide explains the standard material grades used in modern slewing bearings, how to read them, and how to select the right combination for your application.

1. Outer Ring&Inner Ring

The rings are the foundation of the bearing. They carry the hardened raceways on which the rolling elements run, so they must combine high strength, good hardenability and long fatigue life.

50Mn (Structural Steel) — the standard choice

50Mn is a medium-carbon structural steel strengthened with manganese (Mn), with a nominal carbon content of 0.50%. It offers a good balance of strength, hardness and wear resistance with moderate hardenability, and it is economical. For most standard applications, 50Mn is the default ring material.

42CrMo (Alloy Steel) — for heavy-duty service

42CrMo is an alloy steel containing 0.42% carbon with chromium (Cr) and molybdenum (Mo). Its higher hardenability, tensile strength, toughness and fatigue resistance make it the preferred material where the bearing is exposed to heavy loads, high impact or high stress in demanding host machinery.

Selection tip: Use 50Mn for general-duty slewing bearings; upgrade to 42CrMo when the application demands higher strength and impact toughness — for example, in large excavators, offshore cranes and heavy-duty wind turbines.

Application Case Study: 42CrMo in Wind Turbine Slewing Bearings

Wind turbines operate under an especially punishing set of conditions. The yaw bearing at the tower top must rotate the nacelle smoothly while constantly absorbing enormous overturning moments from the rotor and blade loads; the pitch bearings at the blade root must adjust blade angle continuously through highly fluctuating, alternating loads over a projected service life of 20 years or more.

For these critical slewing bearings, 42CrMo is widely preferred for the rings. Its high hardenability ensures that the large ring cross-sections achieve a uniform, deep hardened layer — a key requirement for bearings too large for simple surface hardening. Its excellent toughness and fatigue resistance allow the raceways to withstand repeated alternating bending and contact stress without developing premature cracks or spalling. As a result, wind turbine slewing bearings manufactured with 42CrMo rings deliver significantly improved reliability and longer maintenance intervals in the field, which translates directly into lower lifetime cost for the operator.

This is precisely why we carefully match material grades to each application rather than applying a one-size-fits-all specification. When your host machinery demands more than a standard 50Mn ring can offer, 42CrMo is the engineering answer.

2. Rolling Elements

The rolling elements (balls or rollers) transfer load between the raceways. They must be extremely hard, wear-resistant and able to withstand repeated contact stress.

GCr15 (High-Carbon Chromium Bearing Steel) — the industry standard

GCr15 contains approximately 1.5% chromium. After heat treatment it reaches hardness in the range of HRC 60 or above, delivering excellent wear resistance and contact fatigue strength. It is equivalent to international grades such as AISI 52100 / DIN 100Cr6.

GCr15SiMn (Bearing Steel with Silicon & Manganese)

GCr15SiMn is a modification of GCr15 with added silicon (Si) and manganese (Mn). The additional alloying elements improve hardenability, making it suitable for larger rolling elements and thicker cross-sections, as commonly found in larger slewing bearings.

3. Cages

The cage (retainer) spaces and guides the rolling elements, preventing them from contacting each other. It is available in one-piece (integral) or segmental designs. The spacer separates individual rolling elements.

20# Steel (Low-Carbon Structural Steel)

Offers good strength, weldability and heat resistance. Suitable for both one-piece and segmental steel cages where strength and rigidity are priorities.

ZL102 Cast Aluminium Alloy

A cast aluminium–silicon alloy that is lightweight, corrosion-resistant and offers good heat dissipation. Commonly used when weight reduction is important; however, it is more brittle and has lower strength than steel.

Nylon / Polyamide (PA66, PA1010, Polyamide Resin)

Engineering plastics with excellent self-lubrication, low friction and good wear resistance. Lightweight and quiet in operation, making them ideal for applications where noise reduction and smooth running matter. Typical grades include PA66 (Nylon 66), PA1010 and general polyamide resins.

Selection tip: Choose steel cages for heavy loads and high temperatures; choose aluminium or nylon where weight, quiet running and cost are priorities.

4. Spacers

Spacer-type slewing bearings separate the rolling elements with individual spacers, and the material choice directly affects friction, wear and service life.

  • Nylon / Polyamide (PA66, PA1010, Polyamide Resin)— the most common choice. These engineering plastics offer excellent self-lubrication and low friction, good wear resistance, light weight, and quiet, smooth operation. They are ideal for applications where reduced friction, noise control and cost-effectiveness matter — such as general-purpose cranes, rotary conveyors and small and medium-sized hoists operating under moderate loads and normal temperatures.
  • ZL102 Cast Aluminium Alloy— a lightweight, corrosion-resistant aluminium–silicon alloy with good heat dissipation. It suits applications where weight reduction and corrosion resistance are priorities, such as outdoor or humid environments and lightly loaded rotating platforms.
  • Selection tip: Choose nylon/polyamide spacers for smooth, low-noise, cost-effective general service; choose ZL102 aluminium spacers when lightweight, corrosion resistance or heat dissipation is the priority. 

5
. Seals

Seals protect the bearing from contamination and retain lubricant. Their material must resist the operating environment, especially oils and chemicals.

NBR (Nitrile Rubber)

The standard seal material for slewing bearings. It offers excellent resistance to mineral oils and fuels, good wear resistance and a cost-effective balance of performance. For most applications, NBR is the default choice.

FKM (Fluororubber)

For demanding environments. FKM withstands high temperatures (up to roughly 200°C and beyond) and resists a wide range of chemicals and aggressive oils. It is more expensive, and is selected where extreme temperature or chemical resistance is required.

Material Selection Quick Reference

Component

Material Grades

Key Characteristics

Typical Applications

Rings

50Mn (standard) / 42CrMo (heavy-duty)

Strength, hardenability, fatigue life

General vs. heavy-load / high-impact service

Rolling elements

GCr15 / GCr15SiMn

Extreme hardness, wear & fatigue resistance

Standard vs. large-diameter bearings

Cages

20# steel, ZL102 Al, nylon / polyamide

Strength vs. light weight & low noise

Heavy-load vs. weight/quiet-sensitive designs

 Spacers

ZL102 Al,/nylon ,polyamide

 light weight & low noise

weight/quiet-sensitive designs

Seals

NBR / FKM

Oil resistance, temperature & chemical resistance

Standard vs. extreme-environment service

 

How to Choose the Right Material Combination

  1. Load magnitude and type — heavier loads and higher tilting moments call for 42CrMo rings and steel cages.
  2. Operating environment — temperature, humidity, chemicals and exposure determine whether FKM seals or corrosion-resistant materials are needed.
  3. Rotation speed and noise — quieter, lighter designs favor nylon cages.
  4. Service life and maintenance — harder bearing steel and quality seals extend service intervals.
  5. Cost — the right material for the job balances performance with economy; avoid over-specification where standard grades suffice.

Conclusion

Material selection is the single most important factor in the reliability and longevity of a slewing bearing. By matching the correct grades for rings, rolling elements, cages and seals to the demands of your application, you ensure optimal performance, durability and cost-effectiveness.

At UWE, we combine precision engineering with decades of expertise in slewing bearing manufacturing. Every bearing is designed and produced with carefully selected materials to meet the specific requirements of your host machinery — from general industrial equipment to demanding wind-power and heavy-lifting applications. Contact our engineering team to discuss the right material specification for your project.